ZJ-B16-S stainless steel turbine flow sensor with premium stainless steel housing, DN8 (1/4") connection, suitable for water purifiers, water treatment equipment, medical equipment and various other applications, featuring excellent corrosion resistance and stability.
ZJ-B16-S DN8 (1/4") Stainless Steel Body
High-precision turbine type electronic flow meter with premium stainless steel housing, featuring excellent corrosion resistance and durability. Suitable for flow measurement of water or similar concentration liquids, especially for applications with higher material requirements.
 | |
 | |
 |
| Product Model | ZJ-B16-S |
|---|---|
| Connection Spec | DN8 (1/4") Female Thread |
| Housing Material | Stainless Steel |
| Shaft Material | Stainless Steel 304 |
| Impeller Material | PA66, Max Temp 80°C |
| Compatible Media | Water or liquids with similar concentration to water |
| Media Temperature | 0 ~ 80°C |
| Flow Range | 1 - 30 L/MIN |
| Measurement Accuracy | ±10% |
| Cable & Wiring | Red-Black-Yellow 22AWG wire, Red=Positive, Black=Negative, Yellow=Signal output; Cable length 35cm |
| Signal Type | Pulse signal, Square wave |
| Duty Cycle | 50% |
| Pulse Characteristic | F(HZ) = [Q] ± 10% (Horizontal test) |
| Max Working Pressure | ≤ 1.75 MPA |
| Working Voltage | DC 5 ~ 24V |
| Max Working Current | 15 mA |
| Output High Level | ≥ (Vcc – 0.5) V (e.g. Vcc 5V, output high >4.5V) |
| Output Low Level | < 0.5 V DC |
1. Listed values are for reference only.
2. Pulses per liter may vary due to media and installation conditions.
3. It is recommended to calibrate pulses per liter according to complete installation conditions.
Ensure no rapid pulsation in the medium
Ensure no reverse pressure shock
Ensure no air in the system
Minimize pressure loss as much as possible
Pay attention to the installation position of the flow meter
Min/Max flow should be within the linear range of the selected flow meter
Clean the system regularly
Avoid current peaks
Wiring errors (power positive, signal line and ground) will damage the flow meter
Do not apply mechanical load to electrical contacts
Avoid moisture on electrical contacts
Avoid stray interference (EMI) through cables (do not lay cables in parallel with high current loads)
To avoid particles and debris entering the product, a filter screen must be installed at the water inlet.
Install the product inside equipment or indoors, do not expose to outdoor or humid/high temperature environments for extended periods.
When magnetic materials or materials that generate magnetic force are near the product, its characteristics may change.
Do not disassemble the product without authorization to avoid damage. Products that have been disassembled are not covered by warranty.
Do not use high-speed air flow to blow the product, as it may cause internal component damage or blockage.
We reserve the right to improve products without prior notice for technical progress.
Water purifiers, drinking fountains, water dispensers, vending machines, water control systems, IC card water meters, smart water meters, hot water meters, campus card systems, bathroom water control systems, industrial cooling systems, circulating water systems, boiler systems, central air conditioning, refrigeration equipment, water treatment equipment, medical equipment, car wash equipment, swimming pool circulation systems, smart machinery equipment, instruments and meters
 | |
 |
| Keywords | ZJ-B16-S stainless steel flow sensor, DN8 water flow sensor, stainless steel turbine flow meter, 1/4 inch flow switch, pulse signal output |
|---|---|
| Page Description | ZJ-B16-S stainless steel turbine flow sensor with premium stainless steel housing, DN8 (1/4") connection, suitable for water purifiers, water treatment equipment, medical equipment and various other applications, featuring excellent corrosion resistance and stability. |
| Tags | ZJ-B16-S|stainless steel flow sensor|turbine flow meter|DN8 water flow sensor|1/4 inch connection |
| Static Page Name | zj_b16_s_stainless_steel_turbine_flow_sensor |