YF-B10-T impeller electronic flow and temperature integrated sensor, featuring premium brass valve body, G1-inch connection, integrated NTC50K temperature probe, capable of simultaneously outputting flow pulse and water temperature signals, suitable for water heaters, wall-hung boilers, water treatment equipment and various other applications.
YF-B10-T G1" (D25) 1-Inch Connection
High-precision impeller electronic flow meter, suitable for flow measurement of water or liquids with similar viscosity. Made with premium brass valve body, offering excellent consistency and long-term stability. Integrated temperature probe can simultaneously output flow pulse and water temperature signals, enabling dual-parameter integrated acquisition.
 | |
 | |
 |
| Product Model | YF-B10-T |
|---|---|
| Connection Specification | G1" (D25) 1-Inch Connection |
| Connection Size | External thread diameter ≈ 32.5mm |
| Overall Dimensions | 75mm*38mm*33mm |
| Housing Material | Premium brass valve body |
| Shaft Material | Stainless steel 304 |
| Impeller Material | PA66, heat resistant up to 80°C |
| Applicable Medium | Water or liquids with similar viscosity to water |
| Applicable Medium Temperature | 0 ~ 80℃ |
| Flow Range | 2 - 50 L/MIN |
| Measurement Accuracy | ±10% |
| Cable and Wiring | Red/Black/Yellow 22AWG wires, Red: positive, Black: negative, Yellow: signal output; cable length 35cm; Two black wires are NTC50K resistor, cable length 15cm; |
| Signal Type | Pulse signal, square wave |
| Duty Cycle | 50% |
| Pulse Characteristic | F(HZ) = [8 * Q]-4 ± 10% (horizontal test) |
| Cumulative Pulse Characteristic | 1(L) = 476Hz ± 10% (horizontal test) |
| Maximum Allowable Pressure | ≤ 1.75 MPA |
| Operating Voltage Range | DC 5 ~ 24V |
| Maximum Operating Current | 15 mA |
| Output Pulse High Level | ≥ (Vcc – 0.5) V (e.g., with Vcc 5V supply, output high level > 4.5V; with Vcc 12V supply, output high level > 11.5V; with Vcc 24V supply, output high level > 23.5V) |
| Output Pulse Low Level | < 0.5 V DC |
| Net Weight | 310g |
1. The values listed are for reference only.
2. The number of pulses per liter may vary depending on the medium and installation conditions.
3. It is recommended to calibrate the number of pulses per liter based on the complete installation.
Ensure there is no rapid pulsation in the medium
Ensure there is no reverse pressure shock
Ensure there is no air in the system
Minimize pressure loss as much as possible
Pay attention to the installation position of the flow meter
The minimum/maximum flow rate should be within the linear range of the selected flow meter
The system should be cleaned regularly
Avoid current peaks
Incorrect wiring of the power positive, signal wire, and ground wire will cause damage to the flow meter
Do not apply mechanical loads to the electrical contacts
Avoid moisture on the electrical contacts
Avoid stray interference through the cable (electromagnetic interference) (do not run the cable in parallel with high-current loads)
To prevent particles and debris from entering the product, a filter screen must be installed at the water inlet of the product.
The product must be installed inside equipment or indoors. Do not expose it to outdoor or harsh environments such as dampness and high temperature for extended periods. The installation must avoid vibrating and shaking environments and applications to prevent affecting the measurement accuracy of the product.
When magnetic materials or materials that generate magnetic force are near the product, its characteristics may change.
Do not disassemble the product without authorization to avoid damage. Products that have been disassembled without authorization are not covered by warranty.
If you have not used this type of sensor before, direct substitution may result in incompatibility. Please take note.
Do not use high-speed airflow to blow into this product, as it will cause internal component damage and jamming, resulting in inaccurate flow characteristics or no output.
We reserve the right to update and iterate the product for technological advancement.
Gas water heaters, electric water heaters, instant water heaters, wall-hung boilers, solar water heaters, heat pump water heating systems, washing machines, dishwashers, smart bathroom equipment, water purifiers, water dispensers, boiling water dispensers, water vending machines, self-service vending machines, water control integrated machines, water control devices, IC card water meters, smart water meters, hot water meters, all-in-one card management systems, campus card water vending systems, bathroom water control systems, industrial cooling systems, circulating water systems, boiler systems, central air conditioning, refrigeration equipment, water treatment equipment, dosing and dispensing equipment, agricultural irrigation systems, chemical metering equipment, pharmaceutical equipment, food and beverage processing equipment, medical equipment, car wash equipment, swimming pool circulation systems, smart mechanical equipment, instruments and meters
 | |
 |
| Keywords | YF-B10-T impeller electronic flow and temperature integrated sensor, G1-inch connection water flow sensor, brass valve body flow meter, NTC50K temperature probe, pulse signal output |
|---|---|
| Page Description | YF-B10-T impeller electronic flow and temperature integrated sensor, featuring premium brass valve body, G1-inch connection, integrated NTC50K temperature probe, capable of simultaneously outputting flow pulse and water temperature signals, suitable for water heaters, wall-hung boilers, water treatment equipment and various other applications. |
| Tags | YF-B10-T|impeller flow sensor|temperature integrated sensor|water flow sensor|brass valve body |
| Static Page Name | yf_b10_t_impeller_electronic_flow_temperature_integrated_sensor |